Kistler
Signal Conditioners
Measurement
& Analysis
Powering, conditioning and computer interface
solutions are available from a suite of electronic
equipment tailored to provide measurement flexibility
with utmost quality and integrity. Couplers from
inexpensive single channel to large, modular,
multichannel platforms can be selected. Charge
amplifiers with dual mode (low and high impedance)
capability offer adaptability to a variety of
sensor configurations.
|
|
Kistler
Cables
Kistler's
Perfect Cable Connection
All Kistler cables are designed to provide optimum
signal transmission. Developed to perform in the
most unusual applications from cryogenic to ultra
high temperature, adverse to laboratory environments,
and available for low or high impedance transduction.
There is a cable specially designed for any and
every need. A wide array of options, including
line length and plug design, are available for
each cable model.
Kistler's premium cables/connectors are rugged,
dependable and assure precision sensor measurements.
Kistler connectors are high quality stainless
steel. Noise and intermittent operation are eliminated
because there is no plating to wear off. Stainless
steel also reduces the weight by 50% compared
to conventional connectors therefore reducing
mass loading in accelerometers. O-rings at each
end seal out moisture and contaminants. A built-in
strain relief replaces shrink tubing provided
a reduced loop radius.
Unlike conventional cables, only low-noise extruded
Teflon cable is used for a
true water tight cable seal and it won't fray
during normal use. These cables can
be used with both low and high impedance sensors
and have a temperature range of -320 to 465°F.
|
|
Kistler
Calibration Equipment
Most Kistler force sensors are factory calibrated
and delivered with a calibration certificate traceable
to national standards. Kistler also offers calibration
services at customer request with minimum turnaround
time.
Features:
• Static and dynamic calibration of pressure sensors
• Pressures to 100,000 psi
• Portable
• IEEE-488 and RC232C interfaces
Pressure Pulse Generator - Capable of generating
impulse pressures of
365 to 72,500 psi over a 5 to 10 millisecond period.
Hydraulic High Pressure Generator - Portable
or stationary generator for
static calibration of high pressure sensors.
Calibrator - Portable, 2 channel, microprocessor-controlled
calibrator
which may be used with Kistler reference sensors
and pressure generators.
|
|
Kistler
Electronics
Kistler
Instruments have unquestionably the largest and
broadest range of electronics/instrumentation
in this market. It would be beneficial to review
the matrix table available to assist and narrow
your range of selection. Refer to detailed data
sheets for operation specifications and options.
Powering, conditioning and computer interface
solutions are available from a suite of electronic
equipment tailored to provide measurement flexibility
with utmost quality and integrity. Couplers from
inexpensive single channel to large, modular,
multichannel platforms can be selected. Charge
amplifiers with dual mode (low and high impedance)
capability offer adaptability to a variety of
sensor configurations. Gain, filtering, and conditioning
aspects of the measurement chain are contained
in this section.
|
|
Kistler
Mounting
The
mounting of accelerometers, force sensors and
pressure transducers are
important considerations
when attaching these products to achieve maximum
response and performance. Kistler has a wide range
of mounting adapters for their extensive range
of transducers.
We suggest you review this section when selecting
a transducer. In addition you
may wish to contact
one of our applications personnel to help guide
you through your selection.
|
|
Kistler
Measuring Instruments/Systems
Kistler
has a great deal to offer
As Kistler's measuring instruments are used in a great variety of fields, separate data is also available
for the following applications:
• Engines
• Vehicles
• Manufacturing
• Plastics Processing
• Biomechanics
|
|
Kistler
Monitoring & Control Units
Kistler
control monitors are used for the integrated monitoring
and control of
production processes. The CoMo
II and CoMo II-S record two associated
measurands
(e.g. press force and "displacement") and evaluate
their functional relationship. The parameters
for the monitoring functions and the methods of
evaluation can be operator selected and adjusted
within wide limits. The monitors
are specifically
designed for process engineering and no special
programming or software knowledge is needed for
the configuration of process evaluation parameters.
|
|
Kistler
Preloading
Set of Preloading Elements for Load Washers
The standardized preloading elements are used for mounting the load washers Types 9001A... 9071A. A set of preloading
elements consists of a preloading bolt, a hexagon nut, a centering sleeve and two insulating washers.
Set of Preloading Elements for Force Sensors
The standardized preloading elements are used
for mounting the multicomponent force sensors
Types 907X with internal diameter of 40.5 mm.
A set of preloading elements consists of a hollow
preloading bolt, a screw nut, a centering sleeve
and a sliding washer.
|
|
